Building Bitcoin node on Raspberry Pi 2

My quest to build inexpensive, minimal Bitcoin node you can “drop behind enemy lines” and forget about it has started some time ago. In the course of time I have made a few attempts to turn original Raspberry Pi into a Bitcon node. All failed miserably. It turned out 512MB of RAM is simply not enough to build a stable node able to withstand exposure to the Bitcoin network. It so far seemed to be mission impossible without patching the Bitcoin Core reference implementation1.

Raspberry Pi 2

The failures from the past have not discouraged me from looking at new devices including the latest Raspberry Pi 2 that went on sale recently. It features 1GB of RAM2 and up to six times the performance of the original device3, all in the same price range.

This tutorial documents the steps required to build a stable Bitcoin node based on the latest device combined with a 64GB microSD card. I hope it will encourage some people to build, run and maintain a full node, and by doing so contribute to the Bitcoin network in a meaningful way.


Before you proceed I have to worn you: I offer this tutorial without any warranty and with the disclaimer that it is your responsibility to find trusted sources to download any required software component, be it a code or binary. It is your call and while I provide some guidance you are on your own and I can not be held responsible for any results of the procedure described here.


  • Raspberry Pi 2 available from shop and multiple suppliers depending on where you are located
  • micoSD card of at least 32GB but if you want to be future proof I would go for a bigger one, the block chain size is quickly approaching 32GB limit
  • A clean install of Raspbian OS on the microSD4

Initial steps

Before you connect your Raspberry Pi to Internet, boot it, login with the default user name pi and password raspberry and run the configuration tool5:

sudo raspi-config

Use menu Expand file system to expand the file system of the Raspbian OS to the full capacity of your microSD card.

Select Internationalization options to:

  • Change locale, make sure that at least “en_US.UTF-8 UTF-8” is selected
  • Change timezone to set your, you guessed it right, time zone

Remember to change the default password, use Change user password menu option. Make sure to chose a strong one6.

Optionally select Advanced options and enable SSH server, this will allow you to access the node remotely.

Quit configuration tool and reboot:

sudo reboot

Connect your Raspberry Pi to Internet, preferably via Ethernet cable7. Check the network interface status with:


The response to the command should look similar to this:

eth0 Link encap:Ethernet HWaddr 00:0F:20:CF:8B:42
inet addr: Bcast: Mask:
RX packets:2472694671 errors:1 dropped:0 overruns:0 frame:0
TX packets:44641779 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:1761467179 (1679.7 Mb) TX bytes:2870928587 (2737.9 Mb)

The “inet addr” should be set to the IP address received from the DHCP server of your router or modem.

Update the Raspbian OS:

sudo apt-get update
sudo apt-get upgrade

If possible avoid using the graphical interface, started with startx command, to save precious memory for the Bitcoin Core demon.

Setting up build environment

Install required dependencies:

sudo apt-get install build-essential autoconf git libssl-dev libboost-dev libboost-chrono-dev libboost-filesystem-dev libboost-program-options-dev libboost-system-dev libboost-test-dev libboost-thread-dev

Create working directory and cd into it:

mkdir ~/work
cd ~/work

Building the database

Compiling Bitcoin Core requires the Berkeley DB version 4.8. Download the database source code, uncompress it, and cd into the uncompressed directory:

tar -xzvf db-4.8.30.NC.tar.gz
cd db-4.8.30.NC/build_unix/

The following commands will configure the compile process, compile and install the database:

../dist/configure --enable-cxx
sudo make install

Note that the compile job with make command will take a while.

Building Bitcoin Core

You are now ready to download the Bitcoin Core code. You may like to directly clone it from github:

cd ~/work/
git clone -b 0.10 bitcoin-0.10
cd bitcoin-0.10

Or instead, as described here, download the official tarball release including the signature, uncompressed it and verify the signature before you proceed further. It is your call to use one of the two options listed above or find your own source or method you feel comfortable with.

The following commands will configure the compilation process, compile the source and check the result:

./configure CPPFLAGS="-I/usr/local/BerkeleyDB.4.8/include -O2" LDFLAGS="-L/usr/local/BerkeleyDB.4.8/lib" --disable-wallet
make check

Again, the compile job with make command will take a good while. Finally after performing the successful check you are ready to install the Bitcoin Core on the system:

sudo make install

You can now run Bitcoin Core from anywhere on the system by simply typing:

bitcoind -dbcache=50 &

It is worth spending some time looking at and experimenting with parameters of the bitcoind demon. The dbcache parameter used here limits the memory cache used by the database to 50MB. Without the limit your node will run out of memory and crush.

Opening the 8333 port

In the final step you need to forward traffic on port 8333 on your home router or modem to the Raspberry Pi. Refer to your router’s user manual and look for “Port Forwarding” option. This typically involves entering the web interface of your network router or modem, and setting up port forwarding there so the traffic coming from Internet on port 8333 is forwarded to the IP address of your node8. You can check if your node is accepting incoming connection here.

Blockchain sync

It will take about three days to sync the complete Bitcoin blockchain consisting of, at the time of writing, 344817 blocks9. The process may still fail despite of the double RAM available on the latest Raspberry Pi. This is why you need to monitor the status of the sync and restart the demon when required. You can check it by issuing the following command.

bitcoin-cli getinfo

These two additional commands may also help to monitor the node status:


Once synced, it is good idea to backup the blockchain or clone the complete microSD card.

That pretty much sums it up.

  1. I have recently found initiative decrufting the Satoshi codebase and I’m going to give it a try hoping it will lead to a better result then the latest official Bitcon Core release I’m using in this tutorial. 

  2. Double the RAM of the previous version. 

  3. It has a quad-core processor that runs at 900MHz, compared to a single-core CPU that ran at 700MHz in the first generation 

  4. Follow to the guide on 

  5. Refer to this tutorial 

  6. You can learn here what it means to create a strong password. Make use of this information anytime you need to create a password. 

  7. There is no reason to expose the node to your wireless network. 

  8. Use ifconfig command to find out what the “inet addr” of the node is. 

  9. You can check latest block number here